Your Pitch Network » Cat

Recognize And Understand Home Networking Components

admin — Wed, 14 Apr 2010 09:23:52 +0000

If you have not decided already,you will soon want to network your two or more computers in your home. You want to be armed to the teach with knowledge of just what it takes to connect your computers to one another.

You first should decide which network is best your you. If your computers are in the same room,the Wireless network should not be considered.The wired by cable network should work just fine.

Computer that may be close to each other but cannot be seen may and have phone jacks close by can easily be networked with the HomePNA Network.While PCs that are far from each other can be connected with the powerline network,assuming wall outlets are nearby.

And when there are computers in different rooms and you want the convenience of moving the systems from room to room,the more expensive Wireless Network is the way to go.After you decide on the type of network that is best for you,knowing what components you’ll need to purchase will be a great help.Let’s take a look at each network and the components needed to get it up and running.

The WIRED ETHERNET NETWORK

If your computers are in the same room,the basic network kit can wire your systems together.Be sure to carefully open any kit or component you purchase and do not damage the box it came in.The purpose for this is to make it easy to return the component if needed.

Basic kits will have instructions and software for the network as seen as two NICs.Better known as Network Interface Cards,these NICs are installed in empty slots in the system unit.The PCI slot is where the card is installed and there are the USB adapters as well.The network will need cabling to connect the computers and the CAT 5 or Category 5 cable is the one to look for.

Ethernet networks come in two speeds,which are 10 and 100mbps or megabits per second.The wired network will also need a Hub or a Switch to direct traffic from each system.If you want fast traffic,and who don’t,you will want to connect a Switch instead of a Hub.If you want all PCs to connect to the Internet,most kits come with Special Bridging Software which links the systems together.

The WIRELESS HOME NETWORK

Wireless networks rely on radio frequency to transmit and receive data.Wireless network equipment will offer you the choice of both wired and wireless connections.

If your computers are in direct line of each other,the IR or Infrared frequency can be used.But most wireless networks now use the Radio Transceiver technology with computers being located just about anywhere.

You will need a Wireless Router to connect each PC to the network.Wireless NIC Cards must be installed in each computer in the network.When you purchase your wireless kit,take note of the indoor range.

As you can see when looking at the wireless Router,you have the option to wire your computers together should something go wrong with any wireless component.Take note of the difference between the wired nic and the wireless nic cards.

The POWERLINE NETWORK

The powerline network uses the electrical wiring in your home to transfer data to and from each computer.Present powerline networks run between 50kbps or Kilobits Per Second and 350kbps.

This network has a drawback in back it will have lots of electrical noise which will cause the network to lose speed.And other PC users can snoop in your computer if they know how.

This network will need a Router for data transfer and nic cards for each system.A Bridge will be needed for access to the internet.These Bridges can be used with your Router.

The PHONELINE NETWORK

The components you will need in the Home Network are close to that of the Wireless network.In most cases,the 10mbps speed network is fast enough for home users.

The computers are connected with a Switch,a gateway,or Router to share Internet access and to send data to each computer through the phone line network.This network is considered the easiest to setup.

Phoneline Network adapters are installed in each PC. The USB or Universal Seriel Bus port connection is the most commonly used adapter for Phoneline networks.To reduce line noise,a Phone Filter may be needed.If you plan to connect a phone and line in one phone jack.you will have to invest in a Line Splitter.Be sure each computer in the network are close to a phone jack.

The Phoneline Network is thought to be less expensive .more dependable and faster when compared with the Powerline network.

In a nutshell,all networks will need some type of adapter inserted in the computer.Each network will need a hub, switch,or router to transfer data.Windows 98,Me,and XP will have the needed software to make everything work together.Adapters and and other hardware will come with device driver software which enables the hardware to talk to the computer.

We have taken a brief look at the hardware needed to network two or more computers.Connecting the hardware was rather simple when we networked our computers using the wireless technology.Learn all you can about PC networking and you will be grateful in having this knowledge should you experience computer problems.

Since we have seen basic network components,its time to see how each component is installed and connected.Then we’re going to see how to move data from one machine to the other and share the internet using broadband with a DSL or a Cable modem.Remember to enjoy learning about your computer by performing as many tasks as you can without causing damage to your system.

Category 6 Cable: A Category above the Rest!

admin — Sun, 07 Feb 2010 18:17:59 +0000

Today’s bandwidth expectations mean that Category 5 is strategically dead. The Category 5 Enhanced (5e) standards, which should have been ratified in August and may be finalized at November’s committee meeting, specify new measurements that provide more margins for 100BaseTX and ATM-155 traffic. Critically, Category 5e standards make reliable Gigabit Ethernet connections possible. But many structured cabling suppliers argue that Category 5e is only an interim solution on the road to Category 6, which will support at least 200 MHz; in the interests of sufficient operating margin, the IEEE is requesting a 250-MHz Category 6 specification. Despite the fact that the Category 6 standards are only at draft stage, manufacturers are offering a host of products and claiming that these products comply with the draft proposals.
What is a category 6 cable? Out of the three cable categories (Cat-5, Cat-5e & Cat-6), Category 6 is the most advanced and provides the best performance. Just like Cat 5 and Cat 5e, Category 6 cable is typically made up of four twisted pairs of copper wire, but its capabilities far exceed those of other cable types because of one particular structural difference: a longitudinal separator. This separator isolates each of the four pairs of twisted wire from the others, which reduces crosstalk, allows for faster data transfer, and gives Category 6 cable twice the bandwidth of Cat 5! Cat 6 cable is ideal for supporting 10 Gigabit Ethernet, and is able to operate at up to 250 MHz. Since technology and standards are constantly evolving, Cat 6 is the wisest choice of cable when taking any possible future updates to your network into consideration. Not only is Category 6 cable future-safe, it is also backward-compatible with any previously-existing Cat 5 and Cat 5e cabling found in older installations.
Category 6, (ANSI/TIA/EIA-568-B.2-1) is a cable standard for Gigabit Ethernet and other network protocols that is backward compatible with the Category 5, category 5e and Category 3 cable standards. Cat-6 features more stringent specifications for crosstalk and system noise. The cable standard is suitable for 10BASE-T / 100BASE-TX and 1000BASE-T (Gigabit Ethernet) and is expected to suit the 10000BASE-T (10Gigabit Ethernet) standards. It provides performance of up to 250 MHz.
The cable contains four twisted copper wire pairs, just like earlier copper cable standards. Although Cat-6 is sometimes made with 23 gauge wire, this is not a requirement; the ANSI/TIA-568-B.2-1 specification states the cable may be made with 22 to 24 AWG gauge wire, so long as the cable meets the specified testing standards. When used as a patch cable, Cat-6 is normally terminated in 8P8C often incorrectly referred to as “RJ-45″ electrical connectors. Some Cat-6 cables are too large and may be difficult to attach to 8P8C connectors without a special modular piece and are technically not standard compliant. If components of the various cable standards are intermixed, the performance of the signal path will be limited to that of the lowest category. As with all cables defined by TIA/EIA-568-B, the maximum allowed length of a Cat-6 horizontal cable is 90 meters (295 feet). A complete channel (horizontal cable plus cords on either end) is allowed to be up to 100 meters in length, depending upon the ratio of cord length: horizontal cable length.
The cable is terminated in either the T568A scheme or the T568B scheme. It doesn’t make any difference which is used, as they are both straight through (pin 1 to 1, pin 2 to 2, etc). Mixed cable types should not be connected in serial, as the impedance per pair differs and would cause signal degradation. To connect two Ethernet units of the same type (PC to PC, or hub to hub, for example) a cross over cable should be used, though some modern hardware can use either type of cable automatically.
Return loss measures the ratio of reflected-to-transmitted signal strength and is the single most difficult test to repeat with consistent results; at Category 6 levels, the difference between a pass and a fail can be the amount of bend in a test cord. Return loss is also causing headaches for connector manufacturers, because the RJ-45 system isn’t up to the job. The final stumbling block with Category 5e ratification concerns the RJ-45 hardware; Category 6 is committed to RJ-45 for backward compatibility, but the ISO’s proposed Category 7 system will have a new and as-yet-unspecified connector to accompany its revised cabling. Today, the return loss problem explains why manufacturers of Category 6 hardware, which is supposed to be interoperable, claim Category 6 performance only if you use the manufacturers’ matched parts throughout a channel link.
The Telecommunications Industry Association (TIA) is working to complete a new specification that will define enhanced performance standards for unshielded twisted pair cable systems. Draft specification ANSI/TIA/EIA-568-B.2-10 specifies cable systems, called “Augmented Category 6″ or more frequently as “Category 6a”, that operates at frequencies up to 500 MHz and will provide up to 10 Gbit/s bandwidth. The new specification has limits on alien crosstalk in cabling systems.
Augmented Category 6 specifies cable operating at minimum frequency of 500 MHz, for both shielded and unshielded. It can support future 10 Gb/s applications up to the maximum distance of 100 meters on a 4-connector channel.

Six Largest Mistakes Made when Hiring a Cabling Contractor

admin — Wed, 13 Jan 2010 18:23:52 +0000

Cabling of data and voice systems is often ignored by many companies until the last minute just before relocation or new building takes place. Many information systems professionals view it as a low priority or something that just takes away from their budget for real network components such as servers or software. However having a state of the art easy to manage cabling system is just as important as good reliable servers on a network. Cabling is the backbone of any computer network; it ties all the components of the network together therefore it should receive as much careful consideration as any other network component.

Mistake number one ? Blindly choosing the lowest bidder

This is the most common mistake made when installing voice and data network cabling. Often the lowest bidder is the contractor who is the smallest, has the least experience or the one that made a mistake on their bid. Prior to making this decision you should know your contractor. Find out how long they have been in business, visit some of the large installations they have done and by all means go visit their offices and warehouse. A site visit to their office will tell you most of what you need to know about an organization. Make sure your contractor has completed jobs of similar scope and size.

Mistake number two ? Choosing the manufactures product that will be installed

Many companies have tried to standardize on a particular manufacture of cabling system. Some of the larger manufactures are Belden, Comscope, Ortronics, AMP and Leviton. You can’t go wrong with any of these big names. However IT managers and corporate executives get hung up on trying to standardize because they believe it will make things easier for the IT staff. The reality of the situation is that if you choose any of the larger names the only components that might not be interchangeable are the faceplates. Of course there are performance criteria as well and they all claim to be the best. Do your own research and choose a manufacture that you feel has a strong company that will be there to stand behind their product should you even need to make a warranty claim

Mistake number three ? Paying too much for the latest cabling technologies

The fact is that today’s network components and network components of the future cannot exceed the specifications of Cat 5E and Cat 6 cabling components. Combine this with the fact that the average company moves every 3 to 4 years. You will find it hard to benefit from future proofing a building you don’t occupy. Look at you current infrastructure, what equipment or applications do you plan to add or upgrade? Is Gigabit or 10 Gigabit Ethernet an option for you in the near future?

Mistake number four ? Not using universal wiring

The EIA/TIA and BICSI both recommend a universal wiring platform for your Communications Infrastructure. In the old days the average install would consist of a single voice grade cable for the phone system and a single data grade cable (Cat 3, Cat5, Cat5E or Cat 6) for their computers. This of course dedicates the usability of these cables to one system type. This is further exacerbated by the termination method used. Voice cables were traditionally terminated on 66 style blocks (66m1-50), which are not user friendly and require a special tool and cross connect wire to make changes. Telephony companies have made a killing for years just performing MAC work (Moves, Adds and Changes) because a customer was unable or unwilling to brave the telephone closet and perform the MAC work themselves.

The practice of using a true universal wiring platform is now the standard for all reputable cabling contractors. A Universal Wiring Platform is made up of all data grade components that are downward compatible for all voice applications. A common installation would consist of 3 Category 5E or Category 6 cables all terminated on a 110 type Patch Panel. At the wall plate all cable would be terminated on the matching grade of 8 position modular jack (incorrectly know as an RJ-45). This design not only allows for maximum flexibility were the customer could have 3 computers or 3 phones or 2 computer and 1 phone or any configuration that works for their application. The point is that now the customer is in complete control of their cabling infrastructure and does not need to pay a contractor to come out every time they move an office. In the long run this will also save you money on the overall cabling system as it will shift and flex to meet your needs without having to bring in your cabling contractor. Remember, having the contractor in after construction has completed will involve them pulling out ceiling tiles and standing on desks while you are trying to do business. The elimination of the disruption alone makes it worth while.

Mistake number five ? No CAD pre installation and post installation CAD drawings.

Most customers really have no idea what their cabling platform will look like when they sign the paperwork. They rely on their contractor to “just do the right thing”. Do not make this mistake, if you don’t understand how your infrastructure will work or what it should look like, don’t sign. Your contractor should have the ability to take your building blue print and overlay his cabling plan on top of your electrical plans. This will give you a visual representation of what you are paying for and allow you to ask questions. Likewise, after the job is complete you should receive what is called an “As Built Drawing” showing all of your communications outlets with a standards based numbering system. Some contractor will even provide a scale elevation plan showing were your patch panels are and how much room you have left in each rack for growth and or other equipment. This should be provided to you both hard copy and in AutoCAD format for your architect to incorporate into your final building As Builts.

Mistake number six ? Not getting a design before the job starts.

This seems to be all over the board, some people have no design plan what so ever. Some will pay $10,000 for an engineering firm to write a specification were they charge by the pound for the spec. Don’t be fooled that a large spec is a good spec. Often a specification filed with time consuming exercises for the bidding contractor and unnecessary pricing breakouts will only prevent good contractors from bidding on your project. What you want is a spec that clearly defines your realistic requirements, requires basic qualification with references and does it as quickly and simply as possible. Do not try to write a spec that will cover every contingency, you will drive your contractor away and you will only confuse the process more. Once you have selected your contractor based on an apple s to apple comparison, you can always and should always sit down to discuss the project and other options that they recommend. One more thing, always, always have the contractor provide you with a parts list with quantities, not individual prices, just quantities. This will help you weed out the contractors that did their homework when you start to compare their list of parts.

Mistake number six ? No cable management

All cabling systems will look organized before they are used, that’s easy. Show me that cabling system after 6 months and I will tell you if the proper wire management was used. “Used” being the key word here. Remember, you can have the best wiring management in the world, if you don’t strictly enforce its use with your IT Staff, you will have a mess. That said, your contractor must provide you with a good design. My recommendation is, listen to your contractor, they know more than you do about this. Then, go visit some of the sites that are done the way they recommend. See how they look after being used a few months. Ask the customer how easy it is to keep organized. Don’t underestimate the value of this step. If your patch panels are a mess and you can’t effect changes in a rapid and orderly fashion then you would have been better off paying your contractor to do the MAC work for you.